TABLE LAMP KITS FOR CERAMIC BASE, GLASS BOTTLE AND WOODEN TABLE LIGHTS


CERAMIC TABLE LAMP KIT - small cap

Bung and Lampholder Kit. You can use our Ceramic Table Lamp Kit to re-wire a ceramic table lamp that has an exit hole for flex already. Simply insert the rubber bung into the aperture at the top of your table lamp and remove the metal reducer that is holding down the plate. You can then access a 'screwdriver slot' to turn to expand the bung to create a tight fit. Replace the reducer to secure the plate again. Feed your flex down the bung & through the hole in your lamp then wire up the lampholder and attach it to the ½" threaded the reducer. Don't forget to order your flex, switch and plug to complete your Ceramic Table Lamp kit. We stock the lamp parts for this kit in a choice of three finishes, antique brass, brass and chrome with small cap in 2 different sized bungs (see selection drop box below). Size 19-22mm fits a standard wine bottle. We highly recommend adding a switch to your flex away from the lamp so as to avoid rocking of the bung which could work its way loose.
Please refer to a qualified electrician if you are not qualified to rewire a table lamp.

Please select 
 Please select   and click   to add to your shopping basket

CERAMIC TABLE LAMP KIT - large cap

Bung and Lampholder Kit. You can use our Ceramic Table Lamp Kit to re-wire a ceramic table lamp that has an exit hole for flex already. Simply insert the rubber bung into the aperture at the top of your table lamp and remove the metal reducer that is holding down the plate. You can then access a 'screwdriver slot' to turn to expand the bung to create a tight fit. Replace the reducer to secure the plate again. Feed your flex down the bung & through the hole in your lamp then wire up the lampholder and attach it to the ½" threaded the reducer. Don't forget to order your flex, switch and plug to complete your Ceramic Table Lamp kit. We stock the lamp parts for this kit in a choice of three finishes, antique brass, brass and chrome with large cap in 3 different sized bungs (see selection drop box below). We highly recommend adding a switch to your flex away from the lamp so as to avoid rocking of the bung which could work its way loose.
Please refer to a qualified electrician if you are not qualified to rewire a table lamp.

Please select 
 Please select   and click   to add to your shopping basket

WOODEN TABLE LAMP KIT

Base Plate and Lampholder Kit. These base plates can be screwed onto your wooden table lamp fittings or standard lamp. Screw on the lampholder then just attach your flex, switch and plug. Comes supplied with 3 matching screws. Available in aged, brass and chrome finishes, this kit is suitable for bases with an exit hole for the flex.

Please select 
 and click   to add to your shopping basket

SIDE ENTRY LAMPHOLDER KIT
FOR WOODEN LAMP WITH NO FLEX HOLE
 

Base Plate, Side Entry Tube, Reducer and Lampholder Kit. This Side Entry Lampholder Kit is suitable for use on a wooden table lamp or standard lamp base with no flex entry hole. Attach the base plate (matching screws are provided) then screw on the side entry tube, reducer and lampholder then add your chosen flex, switch and plug.

Please select 
 and click   to add to your shopping basket

SIDE ENTRY LAMPHOLDER KIT - small cap
FOR CERAMIC BASE OR GLASS BOTTLE LAMPS
 

Bung, Side Entry Tube and Lampholder Kit. This Side Entry Lampholder Kit can be used for a ceramic table lamp base or glass bottle that does not have an exit hole for the flex. Simply insert the rubber bung into the aperture at the top of your bottle/table lamp and remove the metal reducer that is holding down the plate. You can then access the 'screwdriver slot and turn to expand the bung to create a tight fit. Secure the plate this time using the side entry tube then put the reducer on top of this. Feed your flex down the side entry tube and out through the plastic grommet. Wire up your lampholder and attach it to the ½" threaded reducer. Don't forget to order your flex, switch and plug to complete your Side Entry Table Lamp kit. We stock the lamp parts for this kit in a choice of three finishes, antique brass, brass and chrome with small cap in 2 different sized bungs (see selection drop box below). Size 19-22mm fits a standard wine bottle We highly recommend adding a switch to your flex away from the lamp so as to avoid rocking of the bung which could work its way loose.
Please refer to a qualified electrician if you are not qualified to rewire a table lamp.

Please select 
 Please select   and click   to add to your shopping basket

SIDE ENTRY LAMPHOLDER KIT - large cap
FOR CERAMIC BASE OR GLASS BOTTLE LAMPS
 

Bung, Side Entry Tube and Lampholder Kit. This Side Entry Lampholder Kit can be used for a ceramic table lamp base or glass bottle that does not have an exit hole for the flex. Simply insert the rubber bung into the aperture at the top of your bottle/table lamp and remove the metal reducer that is holding down the plate. You can then access the 'screwdriver slot' and turn to expand the bung to create a tight fit. Secure the plate this time using the side entry tube then put the reducer on top of this. Feed your flex down the side entry tube and out through the plastic grommet. Wire up your lampholder and attach it to the ½" threaded reducer. Don't forget to order your flex, switch and plug to complete your Side Entry Table Lamp kit. We stock the lamp parts for this kit in a choice of three finishes, antique brass, brass and chrome with large cap in 3 different sized bungs (see selection drop box below). We highly recommend adding a switch to your flex away from the lamp so as to avoid rocking of the bung which could work its way loose.
Please refer to a qualified electrician if you are not qualified to rewire a table lamp.

Please select 
 Please select   and click   to add to your shopping basket

If you want to raise any of the Lampholder Kits add the following additional items shown below in multiples of 2", 4", 8" & 12".


12" RAISER - rod & coupler

Please select 
 and click   to add to your shopping basket

8" RAISER - rod & coupler
Please select 
 and click   to add to your shopping basket

4" RAISER - rod & coupler
Please select 
 and click   to add to your shopping basket

2" RAISER - rod & coupler
Please select 
 and click   to add to your shopping basket

Click on an image to be taken to the relevant shop page for more details of an item. Select your finish and add to the basket to buy the item selected. You can edit your purchases once in the shopping basket to make variations or additions to your selections.