4 inch Archives - Lamps and Lights

Table Lamp Shade Carrier

£18.20 – £22.20

Colour options available
Bulb holder types available
Edison Screw, Bayonet Cap
PRODUCT DETAILS
Table Lamp Shade carrier for rimmed shade

£26.00 – £27.90

Colour options available
Bulb holder types available
Edison Screw, Bayonet Cap
PRODUCT DETAILS
Table Lamp Harps

£11.10 – £11.80

Bulb holder types available
Edison Screw, Bayonet Cap
PRODUCT DETAILS

Bulb holder types explainedDenise2021-04-28T15:26:55+01:00

Bulb holder types explained

SBC – small bayonet cap fitting takes a SBC bulb. Also known as B15d . Cap measures 15mm across.
BC – bayonet cap fitting takes a BC bulb. Also known as B22d. Cap measures 22mm across.
SES – small edison screw fitting takes a SES bulb. Also known as E14. Cap measures 14mm across.
ES – edison screw fitting takes an ES bulb. Also known as E27. Cap measures 27mm across.
GES – giant edison screw fitting takes a GES bulb. Also known as E40. Cap measures 40mm across.

Do I need 2 or 3 core lamp flex?Denise2021-11-10T16:05:48+00:00

Do I need 2 or 3 core lamp flex?

When using any metal light fittings you need to earth the fitting to reduce the risk of electric shock. You therefore need to use our 3 core light flex in either our round or twisted braid as both have live, neutral and earth wires. Our 2 core braided flex only has live and neutral wires and therefore is only suitable for use with non-metal light fittings. If in any doubt please always refer to a qualified electrician.

Watch video in new window

Do you provide any Electrical or Restoration Services?Denise2021-08-06T14:44:05+01:00

Do you provide any Electrical or Restoration Services?

We do not undertake the restoration or wiring up of our products. We sell components individually not fitted together. Once we put them together we would have to send them off to be PAT tested. You can buy the components and get an electrician to put them together and PAT test them for you?

Need an Electrician to put our products together? You can find one in your area here NICEIC or here ECA
Need a Restorer? You can find one here BAFRA

Hanging Lampshades with a BC or ES holeDenise2021-11-10T14:45:06+00:00

Hanging Lampshades with a BC or ES hole

For Lamp shades weighing less than 2 kg you can use a cord grip lampholder with shade rings to hang your shade.
Then choose between a Bayonet Cap version with shade rings for a shade with a 32mm – 35mm hole; or an Edison screw version with shade rings for a shade with a 38mm – 45mm aperture. Next you need a ceiling rose with a cord grip and some earthed 3 core flex which will go between the lamp holder and the ceiling rose.

For shades over 2kg you need to support the flex by using some lighting chain and therefore need a lampholder with a hook and shade rings to hang your light shade. Then choose between a Bayonet Cap version with shade rings for a shade with a 32mm -35mm hole or an Edison screw version with shade rings for a shade with a 38mm – 45mm aperture. Next you need a ceiling rose with a hook and again some earthed 3 core flex which goes between the lampholder and the ceiling hook. The chain you need is our large link chain. This is sold in max of 10m single length. If your drop is more than that, lengths of chain can be joined using an S hook. Max shade weight is 5kg using a single hook. Please see our Weight tolerance FAQ if your shade is heavier than 5kg.

Don’t forget your LED light bulb!

How do I fit the bungs into a Bottle or Ceramic base?Denise2020-11-04T14:33:03+00:00

How do I fit the bungs into a Bottle or Ceramic base?

You can access a ‘screwdriver slot’ to turn to expand the bung to create a tight fit by removing the reducer that holds down the metal plate. Feed your 3 core braided flex down the bung and through the hole in your lamp then wire up the lampholder and attach it to the ½” threaded reducer on top of the bung. Size 19-22mm fits a standard wine bottle.

How do I hang a rimless shade?Denise2021-11-10T14:49:12+00:00

How do I hang a rimless shade?

You can watch this video on our website to see how.

Watch video in new window

How do I hang a shade with a 10mm hole?Denise2021-11-10T15:11:06+00:00

How do I hang a shade with a 10mm hole?

Use one of our 10mm galleries as shown below. The central brass all thread undoes and goes through the 10mm hole in your shade then re attach the cord grip to secure the shade. You then choose the flex you want to hang down to your cord grip lampholder and up through the hole in the hook via some lamp chain to your ceiling hook.

10mm shade carrier

How do I hang a shade with a rim?Denise2021-11-10T15:04:24+00:00

How do I hang a shade with a rim?

Watch video in new window

How do I stop my lamp flex from fraying?Denise2020-11-04T15:35:03+00:00

How do I stop my lamp flex from fraying?

The simplest most common solution is to apply electrical tape around the end of the cable and then cut over the tape. We stock various colours to match or compliment our lamp flex colours.

How to attach a Ceiling PendantDenise2021-11-10T14:47:43+00:00

How to attach a Ceiling Pendant

How to wire up lampholders?Denise2021-04-28T14:37:55+01:00

How to wire up lampholders?

The earth is marked in the middle of the insert. The live is the one that from underneath you can see goes across to the centre of the insert.

We also have a list of useful “How to” videos on our YouTube channel that includes a video “Metal Bayonet Lampholder Wiring & Testing” where you can see our bayonet cap lamp holder being wired up and tested by an Electrician.

Please do check your work with an electrician though as this advice is strictly general & can vary depending on many factors relating to the individual use of a product and your domestic set up.

I’m having trouble putting the side entry lamp holder kit together?Denise2022-03-15T16:57:31+00:00

I’m having trouble putting the side entry lamp holder kit together?

Our side entry lamp holder kits are usually put together for you. If not, you just need to switch the reducer round.

Undo the reducer screwed on the top of the bung.
Screw the side entry tube onto the bung where the reducer came off.
Put the reducer on top of the side entry tube ready for your lampholder.

The side entry tube is now the right way up so the flex can be gripped by the black grip screw above the entry hole in the tube.

What are your products weight tolerances?Denise2021-12-13T10:12:29+00:00

What are your products weight tolerances?

For Lamp shades weighing less than 2 kg you can use a cord grip lampholder to hang your shade as this is the weight tolerance of the lighting flex.

Our Single Ceiling Hooks can hang, using a piece of our large chain, a light fitting up to max of 5kg. If you had 2 hooks & large chain you could hang 10kg and with one of our large triple hooks and large chain up to a maximum of 15kg. Obviously the fixing into the ceiling needs to be secure, you can add one of our wooden pattresses which can be secured using larger screws. If you fix this into a ceiling joist this can also add extra hold but you will need to consult a builder or electrician if hanging a heavy light fitting to keep you safe.

Our smaller chain is only suitable for hanging a ceiling bowl from our Triple bag ceiling hook as the chain link size is too small to fit over our larger hooks. The maximum weight of the shade should be 5kg as this is the weight tolerance of the triple ceiling hook.

What size are your light shades?Denise2022-02-14T12:55:48+00:00

What size are your light shades?

Small 120-150mm wide

Medium 160-210mm wide

Large 220-290mm wide

Extra Large 300-340mm

X extra large 350mm+

What’s the biggest size bung you do?Denise2019-12-19T12:39:42+00:00

What’s the biggest size bung you do?

Our biggest bung is currently 50mm. You can use some cork or wood to fill the hole if the aperture is bigger than that and insert our fittings into that.

Which regulations apply and bathroom lighting Zones?Denise2022-02-14T15:13:43+00:00

Which regulations apply and bathroom lighting Zones?

Are you qualified? Installing our lighting is not particularly complex, but carried out incorrectly could prove dangerous. Electrical work is a skilled profession requiring expert knowledge with ever changing rules and accreditations. Electrical contractors are required to regularly update their qualifications. We strongly advise therefore that you instruct a fully qualified NICEIC registered electrician to check and electrically test your work. As a supplier we are not qualified or insured to advise you on how to wire up your lighting schemes so any advice given is of a purely general nature. When selling your home you may also need to provide certification for any electrical work undertaken so certification would be useful then too.
Can I use your products in my Bathroom? IP rated lighting must be used in bathroom areas where water is likely i.e. zones 1 and 2. Un-zoned areas can use standard lighting without an IP rating, See our handy diagram for more help. Bathroom Zones Explained

Which wire is which on the clear lighting cable?Denise2020-10-22T14:40:12+01:00

Which wire is which on the clear lighting cable?

To enable the ‘clear look’ to our clear flex, the individual wires are not coloured. Therefore you will need a voltage tester to establish which of the wires are live and neutral. Please always consult a qualified electrician if in any doubt as to the safe use of our products in your project.